Mustafa, Ammar A. and Ibrahim, Maan and Junaidi, termizi and Akhtaruzzaman, Md. (2009) Shear bond strength of three different bonding agents on three different tooth substrates in different times. In: FDI Annual World Dental Congress 2009, 2-5 September 2009, Singapore. (Unpublished)
![[img]](http://irep.iium.edu.my/4176/1/Poster_FDI.jpg) |
PDF
Restricted to Registered users only Download (2MB) | Request a copy |
Abstract
Introduction: The importance of high tensile strength in the adhesion of resin materials to enamel, and particularly to dentin, for the creation of well-sealed and long lasting restorations has often been detailed. However, most of these tests are done after a 24 hours or longer periods. These studies though important in indicating the ability of the bonding resin to adhere to tooth substrate; do not discourse the strength immediately after the bonding resin is cured. Early bond strength can be considered very significant because this is the period when high stresses are placed on the bond among the cavity wall, bonding resin and resin composite. If the bond strength is not strong enough during the first hour after cure, it may rupture, causing gap formation. Investigations of the repair of composites have shown that bond strength can be significantly reduced at an interface involving an aged composite Objectives: The aim of this in vitro study was to investigate the early shear bond strength of two bonding systems on three different tooth substrates and compare the results with other test times and then estimate the obtained results by using SEM, AFM and 2D optical analyser to evaluate the significance of these methods. Materials and methods: 240 human premolars teeth have been collected for this study. All the specimens’ teeth were free of any carious lesion. Three human tooth substrates were used. The first substrate was clean, unprepared enamel. Relatively flat coronal areas were cleaned with a fluoride free pumice flour slurry and rubber cup for 10 seconds and rinsed for another 10 seconds. No other preparations were performed prior to etching. The second and third substrates were prepared enamel and dentin. These specimens were prepared using a model trimmer with coarse and fine silicon carbide wheels and rinsed for 10 seconds. These specimens were also cleaned with fluoride free pumice flour slurry and rubber cup for 10 seconds and rinsed with an air water syringe for another 10 seconds. the embedding moulds used to hold the specimens were made of methylmethacrylate resins. the moulds dimension were 1 inch in height and 1 inch in width. Care was taken to remove any air pocket around the edges of the specimen holes to prevent leakage of the embedding resin. each tooth substrate was positioned within its specimen hole using a small amount of sticky wax, if necessary, to secure uncut specimens. 80 specimens were prepared for the sound enamel in a fact of 20 specimens for each test period, respectivley, one-hour, 24 hours, 7 days and 28 days. 80 specimens were prepared for the prepared enamel and 80 specimens for the dentin in the same distribution as the group for the sound enamel. A cubical specimens of commercial denatl composite were prepared with dimensions of 4 mm. All the test surfaces have been etched with (Actino Etch, 37% Phosphoric Acid Etching Gel, Dental Etchant 1 x 5mL, UK) and then, the composite cubes have attached to the different tooth substrates mounted into the test moulds by the use of test bonding agents. Two bonding agents have been used in the study. 3M ADPER Single Bond 2 adhesives (10 %, 5 nm, colloidal filler) (3M, ESPE, USA). OptiBond Solo adhesive system (15 % filled with 0.4 micron barium glass) (Kerr USA). During the storage period, all the specimens were kept in a solution of artificial saliva in a temperature simulating that of human body with an average of 36 °C. and the storage solution was replaced every 1-2 days. The ready specimens were subjected to failure by Schimadzu Precision Universal Tester AG-X series (Schimadzu corp. Japan) with a cross head speed of 0.1 mm/second. After testing the specimens, the they were removed from the moulds and sectioned by the use of IsoMet 5000 (Buehler, USA) and then tested under scan electron microscopy to check for the bonding embeddement of the bonding agent into the dentinal tissues. The same specimens were evaluated under Atomic Force Microscopy AFM (nanoWizard II KPK, Germany) and by 2D optical surface texture analyzer (non-contact type) (Alicon, Austria). The results oobtained by these different methods were compared and analysed. Statistical analysis: A one-way analysis of variance (ANOVA) was used to determine if there were differences between materials bonded to different surfaces. When the ANOVA proved significant Tukey's multiple comparison test was used to determine the nature of the differences. Benferroni was used to confirm significance. Results: The results shown no significant difference between 1-hour and 24 hours for all groups. The collected results revealed an increase in shear bond strength from 1-hour to 24 hours, 7 days and 28 days respectively but with no significant difference among these test periods. There was no significan difference between the test groups in spite of the fact that 3M ADPER Single Bond 2 has shown higher numerical values after 24 hours. The estimation of the specimens by the use of different methods revealed that the use of SEM is more reliable that the other mothods used in this study in estimating the hybrid layer and the depth of the polymerised bonding agents into the etched dentin or enamel.
| Item Type: | Conference or Workshop Item (Poster) |
|---|---|
| Additional Information: | 5543/4176 |
| Uncontrolled Keywords: | Shear bond strength,bonding agents, tooth substrates |
| Subjects: | R Medicine > RK Dentistry |
| Kulliyyahs/Centres/Divisions/Institutes (Can select more than one option. Press CONTROL button): | Kulliyyah of Dentistry |
| Depositing User: | Assistant prof. Dr. Ammar Mustafa |
| Date Deposited: | 28 Dec 2012 16:22 |
| Last Modified: | 28 Dec 2012 16:22 |
| URI: | http://irep.iium.edu.my/id/eprint/4176 |
Actions (login required)
 |
View Item |
Download Statistics
Download Statistics