Browse by Email

Article

Amin, A. K. M. Nurul and Majed, A. Fakhruzi and Daud, M. K. and Patwari, Md Anayet Ullah and Ishtiyaq, M. H. (2011) Investigation of the machinability of Inconel 718 in room temperature and preheated conditions. Advanced Materials Research, 264-65. pp. 1187-1192. ISSN 1022-6680

Mokhtar, Suhaily and Amin, A. K. M. Nurul and Patwari, Md Anayet Ullah and Abdul Razak, Nurhayati (2011) Machinability improvement by workpiece preheating during end milling AISI H13 hardened steel. Advanced Materials Research, 264-65 (2). pp. 894-900. ISSN 1662-8985

Ullah Patwari, Mohammed Anayet and Amin, A. K. M. Nurul and Istihyaq , M.H. and Faris, Waleed Fekry (2010) Development of a mathematical model for the prediction of chip formation instability and its verification by fuzzy logic with genetic algorithm. International Journal of Machining and Machinability of Materials (IJMMM), 8 (1/2). pp. 38-54. ISSN 1748-572X

Book Chapter

Hossain, Mohammad Ishtiyaq and Amin, A. K. M. Nurul and Patwari, Muhammed Anayet Ullah (2011) Artificial neural network algorithm for predicting the surface roughness in end milling of Inconel 718 alloy. In: Advanced Machining Towards Improved Machinability of Difficult-to-Cut Materials. IIUM university press, International Islamic University Malaysia, Kuala Lumpur, Malaysia, pp. 149-154. ISBN 9789674181758

Hossain, Ishtiaq and Amin, A. K. M. Nurul and Patwari, Muhammed Anayet Ullah and Ginta, Turnad Lenggo (2011) Assessment of performance of uncoated and coated carbide inserts in end milling of Ti-6Al-4V through modelling. In: Advanced Machining Towards Improved Machinability of Difficult-to-Cut Materials. IIUM Press, International Islamic University Malaysia, Kuala Lumpur, Malaysia, pp. 195-202. ISBN 9789674181758

Amin, A. K. M. Nurul and Mokhtar, Suhaily and Patwari, Muhammed Anayet Ullah and Hazim, A. and Adlan, Z. (2011) Comparison of machinability of ceramic insert in room temperature and cryogenic cooling conditions during end milling inconel 718. In: Advanced Machining Towards Improved Machinability of Difficult-to-Cut Materials. IIUM Press, Kuala Lumpur, Malaysia, pp. 209-215. ISBN 9789674181758

Hossain, Ishtiaq and Amin, A. K. M. Nurul and Patwari, Muhammed Anayet Ullah (2011) Development of an artificial neural network algorithm for predicting the cutting force in end milling of Inconel 718 alloy. In: Advanced Machining Towards Improved Machinability of Difficult-to-Cut Materials. IIUM Press, Kuala Lumpur, Malaysia, pp. 143-148. ISBN 9789674181758

Amin, A. K. M. Nurul and Hossain, Ishtiaq and Patwari, Muhammed Anayet Ullah (2011) Wear mechanism in end milling of Inconel 718. In: Advanced Machining Towards Improved Machinability of Difficult-to-Cut Materials. IIUM Press, Kuala Lumpur, Malaysia, pp. 239-245. ISBN 9789674181758

Proceeding Paper

Patwari, Muhammed Anayet Ullah and Faris, Waleed Fekry and Amin, A. K. M. Nurul and Loh, S. K. (2009) Finite element and experimental analysis of dynamic behaviour of Vertical Machining Centre Components by Modal Analysis. In: Advanced Materials for Application in Acoustics and Vibration, 4-6 January 2009, Cairo, Egypt.

Ishtiyaq, M. H. and Amin, A. K. M. Nurul and Karim, A.N. Mustafizul and Ginta, Turnad Lenggo and Patwari, Muhammed Anayet Ullah (2007) Application of response surface methodology coupled with genetic algorithm in the optimization of cutting conditions for surface roughness in end-milling of Inconel 718 using coated WC-co inserts. In: 4th International Conference on Leading Edge Manufacturing in the 21st Century (LEM 21), , 7-9 November 2007, Fukuoka, Japan..