Items where Author is "Mokhtar, Suhaily"

Article

Dahnel, Aishah Najiah and Abdul Ghani, Muhamad Ali and Raof, Natasha A. and Mokhtar, Suhaily and Muhamad Khairussaleh, Nor Khairusshima (2022) Analysis of defects on machined surfaces of aluminum alloy (Al 7075) using imaging and topographical techniques. International Journal of Metrology and Quality Engineering (IJMQE), 13. pp. 1-8. ISSN 2107-6839 E-ISSN 2107-6847

Meera Mydin, Nur Munirah and Dahnel, Aishah Najiah and A. Raof, Natasha and Muhamad Khairussaleh, Nor Khairusshima and Mokhtar, Suhaily (2022) Comparison of tool wear mechanisms during drilling of aluminium alloy 7075 in dry and chilled air conditions. Journal of Science and Technology, 14 (1). pp. 67-74. ISSN 2229-8460 E-ISSN 2600-7924

Dahnel, Aishah Najiah and Fauzi, Muhammad Haziq and A. Raof, Natasha and Mokhtar, Suhaily and Muhamad Khairussaleh, Nor Khairusshima (2022) Tool wear and burr formation during drilling of aluminum alloy 7075 in dry and with cutting fluid. Materials Today: Proceedings, 59 (2022). pp. 808-813. ISSN 22147853

Ramli, Siti Fatirah and Muhamad Khairussaleh, Nor Khairusshima and Mokhtar, Suhaily and Dahnel, Aishah Najiah and A. Raof, Natasha (2022) Optimization of machining parameters values during milling on carbon fiber reinforced plastic (CFRP) using RSM. Malaysian Tribology Society, 34. pp. 24-38. E-ISSN 2289-7232

Meera Mydin, Nur Munirah and Dahnel, Aishah Najiah and A. Raof, Natasha and Muhamad Khairussaleh, Nor Khairusshima and Mokhtar, Suhaily (2021) The effect of chilled air on burr formation when drilling aluminium alloy in manufacturing industry. International Journal of Progressive Sciences and Technologies (IJPSAT), 28 (1). pp. 437-445. ISSN 2509-0119

Mokhtar, Suhaily and Yusof, Nur Syahira Sofyani and Mohd Asri, Mohd Ashraff and Che Haron, Che Hassan and A. Raof, Natasha and Muhammad Khairusalleh, Nor Khairusshima and Dahnel, Aishah Najiah (2020) Effects of drilled area temperatures on drilling of NFRP composites: a review. TEST Engineering & Management, 83 (May – June 2020). 1314 -1321. ISSN 0193-4120

Mokhtar, Suhaily and A. Raof, Natasha and Muhammad Khairusalleh, Nor Khairusshima and Dahnel, Aishah Najiah (2020) A review on the application of various MQL base in metal cutting operation of aluminum alloys. Test Engineering and Management, May-June 2020. pp. 1168-1174. ISSN 0193-4120

Meera Mydin, Nur Munirah and Dahnel, Aishah Najiah and A. Raof, Natasha and Muhamad Khairussaleh, Nor Khairusshima and Mokhtar, Suhaily (2020) The effect of cutting parameters on tool wear in drilling aluminium 7075. TEST Engineering & Management, 83 (May-June). pp. 1274-1280. ISSN 0193-4120

Daud @ Ab Aziz, Nur Sofwati and A. Raof, Natasha and Ghani, Abdul Rahman and Dahnel, Aishah Najiah and Mokhtar, Suhaily and Muhamad Khairussaleh, Nor Khairusshima (2020) Cutting tool performance in turning of AL 7075-t651 aluminium alloy. IIUM Engineering Journal, 21 (2). pp. 177-185. ISSN 1511-788X E-ISSN 2289-7860

Tomadi, Siti Haryani and Mokhtar, Suhaily and Hassan, Mas Ayu and Daud, Rosdi (2020) Prediction of cutting force by using finite element method in end-milling of AISI 1018 medium carbon steel. TEST Engineering and Management, May – June 2020. 1067 -1071. ISSN 0193-4120

Azmi, H. and Che Haron, Che Hassan and A. Ghani, Jaharah and Mokhtar, Suhaily (2018) Comparison effect of delamination factor (Fd) on unidirectional and woven kenaf fibre reinforced plastic composite materials during milling process [Pembandingan kesan faktor pelekangan (Fd) ke atas bahan komposit plastik bertetulang ekaarah dan bertenun semasa proses pemesinan kisar]. Sains Malaysiana, 47 (4). pp. 829-838. ISSN 0126-6039

Mohd Ali, Afifah and Janal, Nurul Nabihah and Hamidon, Nor Ezzati and Ahmad Azhar, Ahmad Zahirani and Mokhtar, Suhaily and Bahar, Rubina and Ahmad, Zainal Arifin (2018) The relationship of cutting chip type, length and thickness to wear of Zirconia Toughened Alumina Added with Magnesium Oxide (ZTA-MgO) cutting tool. International Journal of Current Science, Engineering & Technology, 1 (Special Issue 1). pp. 452-457. ISSN 2581-4311

Mokhtar, Suhaily and Che Haron, Che Hassan and A. Ghani, Jaharah and Harun, Azmi (2017) Evaluation of thrust force in drilling of woven kenaf fiber reinforced epoxy composite laminates. Journal of Mechanical Engineering, SI 3 (1). pp. 149-169. ISSN 1823-5514 E-ISSN 5520-164X

Harun, Azmi and Che Haron, Che Hassan and A.Ghani, Jaharah and Mokhtar, Suhaily (2016) Study on machinability effect of surface roughness in milling kenaf fiber reinforced plastic composite (unidirectional) using response surface methodology. ARPN Journal of Engineering and Applied Sciences, 11 (7). pp. 4761-4766. ISSN 1819-6608

Mokhtar, Suhaily and Amin, A. K. M. Nurul and Patwari, Md Anayet Ullah and Abdul Razak, Nurhayati (2011) Machinability improvement by workpiece preheating during end milling AISI H13 hardened steel. Advanced Materials Research, 264-65 (2). pp. 894-900. ISSN 1662-8985

Book Chapter

Amin, A. K. M. Nurul and Mokhtar, Suhaily and Patwari, Muhammed Anayet Ullah and Hazim, A. and Adlan, Z. (2011) Comparison of machinability of ceramic insert in room temperature and cryogenic cooling conditions during end milling inconel 718. In: Advanced Machining Towards Improved Machinability of Difficult-to-Cut Materials. IIUM Press, Kuala Lumpur, Malaysia, pp. 209-215. ISBN 9789674181758

Amin, A. K. M. Nurul and Mokhtar, Suhaily and Ab. Razak, Nur Hayati (2011) Machinability aspects in heat assisted machining of hardened steel AISI H13 using coated carbide tool. In: Advanced Machining Towards Improved Machinability of Difficult-to-Cut Materials. IIUM Press, Kuala Lumpur, Malaysia, pp. 27-33. ISBN 9789674181758

Proceeding Paper

Rosli, Muhammad Izzat Amin and A. Raof, Natasha and Dahnel, Aishah Najiah and Mokhtar, Suhaily and Muhamad Khairussaleh, Nor Khairusshima (2023) Investigation of chip formation during turning of aluminum alloys 7075-T651 in dry and chilled air condition. In: 5th International Conference on Advances in Manufacturing and Materials Engineering, 9-10 August 2022, Kulliyyah of Engineering, IIUM.

Haszerin, Muhammad Na'iim and A. Raof, Natasha and M Zamre, M K A and Dahnel, Aishah Najiah and Mokhtar, Suhaily and Muhamad Khairussaleh, Nor Khairusshima (2023) Machining performance of carbide insert in turning aluminum alloy 7075-T651. In: International Conference on Manufacturing Engineering Technology (ICONMET 2021), 14-15 July 2021, Asenia Resort, Langkawi, Malaysia.

Dahnel, Aishah Najiah and Fauzi, Muhammad Haziq and A. Raof, Natasha and Mokhtar, Suhaily and Muhamad Khairussaleh, Nor Khairusshima (2022) Tool wear and burr formation during drilling of aluminum alloy 7075 in dry and with cutting fluid. In: Third International Conference on Recent Advances in Materials and Manufacturing 2021, 25-26 November 2021, India.

Ramli, Siti Fatirah and Muhamad Khairussaleh, Nor Khairusshima and Mokhtar, Suhaily and Dahnel, Aishah Najiah and A. Raof, Natasha (2022) Optimization of machining parameters during milling of carbon fibre reinforced plastics. In: 3rd Malaysian International Tribology Conference, MITC 2020, 28 - 30 September 2020, Langkawi, Malaysia.

Mokhtar, Suhaily and Che Haron, Che Hassan and A. Ghani, Jaharah and Harun, Azmi and Mohd Ali, Afifah and Muhamad Khairussaleh, Nor Khairusshima (2018) Study on drilling induced delamination of woven kenaf fiber reinforced epoxy composite using carbide drills. In: 2018 6th International Conference on Nano and Materials Science (ICNMS 2018), 15th-17th January 2018, Lakeland; United States.

Mokhtar, Suhaily and Che Haron, Che Hassan and A. Ghani, Jaharah and Mohd Ali, Afifah and Mohd Khairussaleh, Nor Khairusshima (2018) Analysis and modeling of delamination factor in drilling of woven kenaf fiber reinforced epoxy using Box Behnken experimental design. In: International Conference on Advances in Manufacturing and Materials Engineering (ICAMME 2017), 8th–9th August 2017, Kuala Lumpur, Malaysia.

Mohd Ali, Afifah and Hamidon, N. E. and Zaki, N. K.M. and Mokhtar, Suhaily and Ahmad Azhar, Ahmad Zahirani and Bahar, Rubina. and Ahmad, Zainal Arifin Azhar (2018) The effect of cutting parameters on the performance of ZTA-MgO cutting tool. In: International Conference on Advances in Manufacturing and Materials Engineering 2017, ICAMME 2017, 8- 9 August 2017, International Islamic University Malaysia (IIUM), Gombak Campus, Kuala Lumpur.

Harun, Azmi and Che Haron, Che Hassan and A. Ghani, Jaharah and Mokhtar, Suhaily and Abdul Rahim, Yuzairi (2018) Machinability study on milling kenaf fiber reinforced plastic composite materials using the design of experiments. In: 3rd International Conference on Science, Technology and Interdisciplinary Research (IC-STAR 2017), 18th-20th Sept. 2017, Bandar Lampung, Indonesia.

Muhamad Khairussaleh, Nor Khairusshima and Zakwan, Muhammad Hafiz and Mokhtar, Suhaily and Shaffiar, Norhashimah and Syed Shaharuddin, Sharifah Imihezri (2018) The optimization study on the tool wear of carbide cutting tool during milling Carbon Fibre Reinforced (CFRP) using Response Surface Methodology (RSM). In: International Conference on Advances in Manufacturing and Materials Engineering 2017 (ICAMME17), 8th-9th August 2017, Kuala Lumpur, Malaysia.

Nurul Amin, A. K. M and Mokhtar, Suhaily and D. Arif, Muammer (2012) Analysis of Machinability of Inconel 718 in High Speed End Milling with Ceramic Inserts Under Room Temperature Conditions. In: UNSPECIFIED.

Mokhtar, Suhaily and Amin, A. K. M. Nurul and Patwari, Anayet Ullah and A. Azhar, A. Hazim and A. R., Zulkhari (2010) Enhancement of machinability of nickel based alloy - inconel 718 by induction preheating in end milling using ceramic inserts. In: IIUM Research, Innovation & Invention Exhibition (IRIIE 2010), 26 - 27 January 2010, Kuala Lumpur.

Amin, A. K. M. Nurul and Mokhtar, Suhaily and Patwari, Muhammed Anayet Ullah and Abdul Razak, Nurhayati (2010) A new technique to improve the machinability of hardened steel AISI H13 in end milling. In: IIUM Research, Innovation & Invention Exhibition (IRIIE 2010), 26 - 27 January 2010, Kuala Lumpur.