Items where Author is "Mohammad , Yeakub Ali"

Article

Mohammed , Baba Ndaliman and Bala, Katsina Christopher and Khan, Ahsan Ali and Mohammad , Yeakub Ali and Abdullahi, Umma and Abdulmumin , Adebisi Adetayo (2015) The effects of sliding parameters on dry wear characteristics of Ti-6Al-4V alloy. Advanced Materials Research, 1115. pp. 213-216. ISSN 1022-6680

Al Hazza, Muataz Hazza Faizi and Mohammed, Baba Ndaliman and Mohammad, Yeakub Ali and Khan, Ahsan Ali (2015) Analyzing the influence of electrical parameters on EDM process of Ti6Al4V alloy using Adaptive Neuro-fuzzy Inference System (ANFIS). International Review of Mechanical Engineering, 9 (3). pp. 237-241. ISSN 1970-8734

Al Hazza, Muataz Hazza Faizi and Mohammed , Baba Ndaliman and muhammad, Hasibul hasan and Mohammad , Yeakub Ali and Khan, Ahsan Ali (2013) Modeling the electrical parameters in EDM process of Ti6Al4V alloy using Neural Network method. International Review of Mechanical Engineering, 7 (7). pp. 1464-1470. ISSN 1970-8734

Mohammed , Baba Ndaliman and Khan, Ahsan Ali and Mohammad , Yeakub Ali (2013) Influence of dielectric fluids on surface properties of electrical discharge machined titanium alloy. Journal of Engineering Manufacture, 227 (9). pp. 1310-1316. ISSN 2041-2975 (O), 0954-4054 (P)

Mohammed Baba, Ndaliman and Khan, Ahsan Ali and Mohammad , Yeakub Ali and M A, Mohammad Hambiyah (2013) Modelling the surface roughness behaviour of an EDMed workpiece with different tool electrodes using DoE. IOP Conference Series: Materials Science and Engineering, 53. pp. 1-8. ISSN 1757-8981

Ndaliman, Mohammed Baba and Khan, Ahsan Ali and Mohammad , Yeakub Ali and Wahid, Zaharah (2012) Determination of influential factors on EDMed surface properties using Plackett-Burman design. World Applied Sciences Journal (WASJ), 21 (spec ). pp. 88-93. ISSN 1818-4952

Mohd Ali, Afifah and Khan, Ahsan Ali and Mohammad , Yeakub Ali (2011) Effect of process parameters on abrasive contamination during water abrasive jet machining of mild steel. Advanced Materials Research, 264-65. pp. 1015-1020. ISSN 1022-6680

Mohammad, Yeakub Ali and Khan, Ahsan Ali and Hamzah, Munirah and Khalid, Nor Azura (2009) Study of material removal rate and electrode wear ratio for micro electrical discharge milling of AISI 420 and Stavax ESR. International Journal of Mechanical and Materials Engineering (IJMME), 4 (3). pp. 300-308. ISSN 1823-0334

Book Chapter

Khan, Ahsan Ali and Mohammed, Baba Ndaliman and Mohammad , Yeakub Ali (2011) Developments in EDM process variables. In: Advanced Machining Processes. International Islamic University Malaysia, Kuala Lumpur, Malaysia, pp. 70-75. ISBN 9789674181628

Mohammad , Yeakub Ali and Mansor, Noor Adila and Mass Duki, Siti Hamizah (2011) Effect of micro end milling tool diameter on minimum chip thickness. In: Advanced Machining Process. IIUM Press, Kuala Lumpur, pp. 113-118. ISBN 9789674181628

-, Abdus Sabur and Mohammad , Yeakub Ali (2011) Fabrication of micro filter by electro discharge machining. In: Advanced Machining Process. IIUM Press, Kuala Lumpur, pp. 159-164. ISBN 9789674181628

Mohammad , Yeakub Ali and -, Muhamad Faizal and Mohamad Asharaf, Asfana Banu and Abdul Rahman, Nur Atiqah (2011) Finish cut of titanium alloy using micro electro discharge milling for nano surface finish. In: Advanced Machining Process. IIUM Press, Kuala Lumpur, pp. 83-88. ISBN 9789674181628

Jaafar, Israd Hakim and Abdul Rahman, Nur Atiqah and Banu, Asfana and Mohammad , Yeakub Ali (2011) Focused ion beam micromachining: technology and application. In: Advanced Machining Process. IIUM Press, Kuala Lumpur, pp. 77-82. ISBN 9789674181628

Khan, Ahsan Ali and Adesta, Erry Yulian Triblas and Mohammad , Yeakub Ali (2011) Formation of micro-cracks and recast layer during EDM of mild steel using copper electrodes. In: Advanced Machining Processes. International Islamic University Malaysia, Kuala Lumpur, Malaysia, pp. 44-48. ISBN 9789674181628

Khan, Ahsan Ali and Adesta, Erry Yulian Triblas and Mohammad , Yeakub Ali (2011) Influence of machining parameters on surface roughness during EDM of mild steel. In: Advanced Machining Process. International Islamic University Malaysia, Kuala Lumpur, Malaysia, pp. 33-37. ISBN 9789674181628

Mohammad , Yeakub Ali and -, Mohd Saifuddin and Abdul Rahman, Nur Atiqah and Mohamad Asharaf, Asfana Banu (2011) Investigation of MRR for finish cut of titanium alloy using micro electro discharge milling. In: Advanced Machining Process. IIUM Press, Kuala Lumpur, pp. 89-94. ISBN 9789674181628

Mohammad , Yeakub Ali and -, Mohd Saifuddin and Abdul Rahman, Nur Atiqah and Mohamad Asharaf, Asfana Banu (2011) Investigation of TWR for finish cut of titanium alloy using Micro Electro Discharge Milling. In: Advanced Machining Process. IIUM Press, Kuala Lumpur, pp. 95-100. ISBN 9789674181628

Mohammad , Yeakub Ali and Mass Duki, Siti Hamizah and Mansor, Noor Adila (2011) Investigation of chip formation and minimum chip thickness in micro/meso milling: Methodology and design of experiment. In: Advanced Machining Process. IIUM Press, Kuala Lumpur, pp. 101-106. ISBN 9789674181628

Sabur, Abdus and Mohammad , Yeakub Ali (2011) Investigation of corner radius using micro wire electro discharge machine. In: Manufacturing management from basic machining to quality product. IIUM Press, Kuala Lumpur, pp. 82-88. ISBN 9789674181659

Mohammad , Yeakub Ali and Mohamad Ashraf, Asfana Banu and Abdul Wahab, Adibah and Abdul Rahman, Nur Atiqah (2011) Investigation of minimum chip thickness in micro end milling of PMMA: Experiment and analysis 800 µm diameter tool. In: Manufacturing management from basic machining to quality product. IIUM Press, Kuala Lumpur, pp. 11-17. ISBN 9789674181659

Mohammad , Yeakub Ali and Mohamad Ashraf, Asfana Banu and Abdul Wahab, Adibah and Abdul Rahman, Nur Atiqah (2011) Investigation of minimum chip thickness in micro end milling of PMMA: experiment and analysis 1.0 mm diameter tool. In: Manufacturing management from basic machining to quality product. IIUM Press, Kuala Lumpur, pp. 18-25. ISBN 9789674181659

Mohammad , Yeakub Ali and -, Asfana Banu and -, Adibah and -, Nur Atikah (2011) Investigation of minimum chip thickness in micro end milling of PMMA: process development. In: Manufacturing management from basic machining to quality product. IIUM Press, Kuala Lumpur, pp. 3-10. ISBN 9789674181659

Sabur, Abdus and M.A., Maleque and Mohammad , Yeakub Ali (2011) Machining of ceramic materials: a review. In: Advanced Machining Process. IIUM Press, Kuala Lumpur, pp. 38-43. ISBN 9789674181628

Mohammad , Yeakub Ali and -, Wan Emira Azaty and -, Nor Suriza (2011) Micro electro discharge machining of micro pillar array: analysis of surface finish. In: Advanced Machining Process. IIUM Press, Kuala Lumpur, pp. 142-147. ISBN 9789674181628

Mohammad , Yeakub Ali and -, Wan Emira Azaty and -, Nor Suriza (2011) Micro electro discharge machining of micropillar array: analysis of material removal rate. In: Advanced Machining Process. IIUM Press, Kuala Lumpur, pp. 148-153. ISBN 9789674181628

Mohammad , Yeakub Ali and Elabtah , Ahmad Chaaban and Alrefaie, Musab Jamal (2011) Micro wire electrical discharge machining of tungsten carbide: analysis of surface roughness. In: Advanced Machining Process. IIUM Press, Kuala Lumpur, pp. 124-129. ISBN 9789674181628

Mohammad , Yeakub Ali and Elabtah , Ahmad Chaaban and Alrefaie, Musab Jamal (2011) Micro wire electrical discharge machining of tungsten carbide: analysis of material removal rate. In: Advanced Machining Process. IIUM Press, Kuala Lumpur, pp. 130-135. ISBN 9789674181628

Mohammad , Yeakub Ali and Elabtah , Ahmad Chaaban and Alrefaie, Musab Jamal (2011) Micro wire electrical discharge machining of tungsten carbide: methodology and procedure. In: Advanced Machining Process. IIUM Press, Kuala Lumpur, pp. 119-123. ISBN 9789674181628

Mohammad , Yeakub Ali and Mansor, Noor Adila and Mass Duki, Siti Hamizah (2011) Micro/meso milling of aluminium alloy 1100: analysis and modelling of minimum chip thickness. In: Advanced Machining Process. IIUM Press, Kuala Lumpur, pp. 107-112. ISBN 9789674181628

Mohammad , Yeakub Ali and -, Muhammad Lutfi and -, Mohamad Ismail Fahmi (2011) Vibration issue in micro end milling. In: Advanced Machining Process. IIUM Press, Kuala Lumpur, pp. 154-158. ISBN 9789674181628

Proceeding Paper

Mohammad, Yeakub Ali and Farhana, Sulaiman and Banu, Asfana and Mohamed, Abd. Rahman and Al Hazza, Muataz Hazza Faizi (2017) Investigation of accuracy in microdrilling with minimum quantity lubrication. In: 7th International Conference on Manufacturing Science and Technology (ICMST 2016), 16th-18th July 2016, Sarawak.

Khan, Ahsan Ali and Ndaliman, Mohammed Baba and Mohammad , Yeakub Ali and Lawal, Sunday Albert and Sulong, Nurul Farhana and Mohamad, Ummu Atiqah Khairiyah (2013) Effect of electrical parameters on performance of Cu-TiC mixed ceramic compact electrode in EDM process. In: 2nd International Conference on Mechanical, Automotive and Aerospace Engineering (ICMAAE 2013), 2-4 July 2013, Kuala Lumpur, Malaysia.

Khan, Ahsan Ali and Ndaliman, Mohammed Baba and Mohammad , Yeakub Ali and Al-Falahi, Muath D. and Ibrahim, Haazin A. and Mustapa, Mohad S. (2013) The Effect of EDM with external magnetic field on surface roughness of stainless steel. In: 2nd International Conference on Mechanical, Automotive and Aerospace Engineering (ICMAAE 2013), 2-4 July 2013, Kuala Lumpur, Malaysia.

Ndaliman, Mohammed Baba and Khan, Ahsan Ali and Mohammad , Yeakub Ali and M A, Mohammad Hambiyah (2013) Modelling the surface roughness behaviour of an EDMed workpiece with different tool electrodes using DoE. In: 5th International Conference on Mechatronics (ICOM'13), 2 – 4 July 2013, Kuala Lumpur, Malaysia.

Ndaliman, Mohammed Baba and Khan, Ahsan Ali and Mohammad , Yeakub Ali and Wahid, Zaharah (2012) Determination of influential factors on edmed surface properties using plackett-burman design. In: IIUM Engineering Congress 2012, 3-5 July 2012, Kuala Lumpur, Malaysia.

Mohd. Zain, Zakaria and Ndaliman, Mohammed Baba and Khan, Ahsan Ali and Mohammad , Yeakub Ali (2012) Electro-discharge machining of SUS 304 stainless steel with TaC powder-mixed dielectric. In: International Conference on Advances in Manufacturing and Materials Engineering (ICAMME 2012), 3-5 July 2012, Kuala Lumpur, Malaysia. (Unpublished)

Mohd Zain, Zakaria and Mohammed, Baba Ndaliman and Khan, Ahsan Ali and Mohammad , Yeakub Ali (2011) Influence of TaC Powder Additive on electrical discharge machining of stainless Steel. In: 2nd International Conference on Mechanical and Manufacturing Engineering 2011 (ICME 2011), 6-7 June 2011, Batu Pahat, Johor.

Khan, Ahsan Ali and Adesta, Erry Yulian Triblas and Mohammad , Yeakub Ali (2010) Influence of process parameters on surface integrity during EDM of mild steel. In: 22nd United Kingdom-Malaysia Engineering Conference 2010, 8-9th April, 2010, London.