Items where Author is "Abd Halim, Nor Farah Huda"

Article

Sukindar, Nor Aiman and Md Yasir, Ahmad Shah Hizam and Azhar, Muhammad Danial and Md Azhar, Muhammad Afif and Abd Halim, Nor Farah Huda and Sulaiman, Mohd Hafis and Haji Ahmad Sabli, Ahmad Syamaizar and Mohd Ariffin, Mohd Khairol Anuar (2024) Evaluation of the surface roughness and dimensional accuracy of low-cost 3D-printed parts made of PLA–aluminum. Heliyon, 10 (4). pp. 1-13. ISSN 2405-8440

Abd Halim, Nor Farah Huda and Mustafa, Aisyah Madihah and Shaharudin, N.S. and Dahnel, Aishah Najiah and Tomadi, Siti Haryani and Ahmad, Zuraida and Adesta, E.Y.T. and Rahman, M. (2023) Tool wear and wear mechanism of WC-Co End Mill during milling of CFRP in sustainable cutting conditions. Materials Science Forum, 1109. pp. 153-158. ISSN 1662-9752

Shahruddin, Najlah Sakinah and Abd Halim, Nor Farah Huda and Mustafa, Aisyah Madihah and Tomadi, Siti Haryani and Mahad, Muhammad Akmal and Adesta, Erry Yulian Triblas (2023) Effect of feed rate on tool wear and surface condition during milling of CFRP. Jurnal Tribologi, 38. pp. 40-48. E-ISSN 2289-7232

Sharuddin, Muhammad Hazman and Sulaiman, Mohd Hafis and Kamaruddin, Shafie and Dahnel, Aishah Najiah and Abd Halim, Nor Farah Huda and Mohd Jamir, Mohd Ridzuan and Abdul-Rani, Ahmad Majdi (2023) Properties and tribological evaluation of graphene and fullerene nanoparticles as additives in oil lubrication. Proceedings of the Institution of Mechanical Engineers, Part J: Journal of Engineering Tribology, Special Issue: MYTRIBOS 2022. pp. 1-10. ISSN 1350-6501 E-ISSN 2041-305X

Mustafa, Aisyah Madihah and Abd Halim, Nor Farah Huda and Tomadi, Siti Haryani and Shahruddin, Najlah Sakinah and Nasaruddin, Ricca Rahman (2022) Analysis on tool wear during milling carbon fiber reinforced polymer in dry, coolant and chilled air condition. Jurnal Tribologi, 36 (March 2023). pp. 99-107. E-ISSN 2289-7232

Tomadi, Siti Haryani and Abd Halim, Nor Farah Huda and Dahnel, Aishah Najiah and Gunasegaran, Umma Sankar and Joo, Eng Lim and Rosman, Amar Syazwan (2022) Optimization study on width of cut and cutting-edge radius during side milling of DAC 55 steel. Jurnal Tribologi, 33. pp. 125-136. ISSN 2289-7232

Abd Halim, Nor Farah Huda and Dahnel, Aishah Najiah and Ismail, Azwa Azmariza and Zainudin, Nur Amanina (2020) An experimental investigation on drilling of aluminum alloy (Al 7075) using high speed steel cutting tools. TEST: Engineering & Management, 83 (May-June). 1451 -1456. ISSN 0193-4120

Sukindar, Nor Aiman and Awang Dahan, Azib Azhari and Abd Halim, Nor Farah Huda and Kamaruddin, Shafie and Sulaiman, Mohd Hafis (2020) The Effect of Printing Parameters on Scaffold Structure Using Low-cost 3D Printer. TEST Engineering & Management, 82. 8255 -8263. ISSN 0193-4120

Sukindar, Nor Aiman and Md Azhar, Muhammad Afif and Abd Halim, Nor Farah Huda and Kamaruddin, Shafie and Sulaiman, Mohd Hafis (2020) The effects of printing parameters on the surface quality of metal composite by using fused deposition modeling. Solid State Technology, 63 (5). pp. 866-874. E-ISSN 0038-111X

Abd Halim, Nor Farah Huda and , Afzeri and Aminanda, Yulfian (2011) Experimental study of cutting parameter for drilling on fabric carbon/epoxy composite laminates. Advanced Materials Research, 311. pp. 240-243. ISSN 1662-8985

Book

Maleque, Md Abdul and Ahmad Azhar, Ahmad Zahirani and Sarifuddin, Norshahida and Syed Shaharuddin, Sharifah Imihezri and Mohd Ali, Afifah and Abd Halim, Nor Farah Huda, eds. (2023) Proceeding of 5th International Conference on Advances in Manufacturing and Materials Engineering. Lecture Notes in Mechanical Engineering (1). Springer, Singapore. ISBN 978-981-19-9508-8

Proceeding Paper

Abd Halim, Nor Farah Huda and Dahnel, Aishah Najiah and Gunasegaran, Umma Sankar and Lim, Joo Eng and Mohamad Amiruddin, M. S. and Tomadi, Siti Haryani (2023) Influence of cutting edge radius (CER) and width of cut (WOC) on tool wear in milling SUS 316 stainless steel. In: Proceeding of 5th International Conference on Advances in Manufacturing and Materials Engineering, 9—10 August, 2022, Kuala Lumpur.

Tomadi, Siti Haryani and Abd Halim, Nor Farah Huda and H., Mas Ayu and R., Daud and Zakaria, Muhammad Ariff (2023) Analysis and optimum machining parameters on surface roughness and material removal rate for titanium alloy in milling machining with MQL. In: Proceeding of 5th International Conference on Advances in Manufacturing and Materials Engineering, 9-10 August, 2022, Kuala Lumpur.

Fathi, Farhah Rusyda and Amir, Dzilal and Nasaruddin, Ricca Rahman and Abd Halim, Nor Farah Huda (2023) Investigating the synthesis of activated carbon from carbon chips of carbon fibre reinforced polymer for the removal of methylene blue. In: Proceeding of 5th International Conference on Advances in Manufacturing and Materials Engineering (ICAMME2022), 9–10 August 2022, Kuala Lumpur, Malaysia..

Fathi, Farhah Rusyda and Amir, Dzilal and Abd Halim, Nor Farah Huda and Nasaruddin, Ricca Rahman (2022) Investigating the Synthesis of Activated Carbon from Carbon Chips of Carbon Fibre Reinforced Polymer for the removal of Methylene Blue. In: Proceeding of 5th International Conference on Advances in Manufacturing and Materials Engineering, 09-10 August 2022, Kuala Lumpur.

Mustafa, Aisyah Madihah and Shahruddin, Najlah Sakinah and Abd Halim, Nor Farah Huda and Rozhan, Alya Naili and Mohd Hatta, Maziati Akmal (2022) The effect of cutting speeds on tool wear and surface roughness when milling carbon fiber reinforced polymer. In: 5th International Conference on Mechanical, Automotive and Aerospace Engineering (ICMAAE 2021), 21-23 June 2021, Kuala Lumpur, Malaysia.

Sukindar, Nor Aiman and Awang Dahan, Azib Azhari and Syed Shaharuddin, Sharifah Imihezri and Abd Halim, Nor Farah Huda (2021) Performance of low-cost 3D printer in medical application. In: Manufacturing Science and Engineering Conference ( Virtual Conference ), United State,Ohio. (Unpublished)

Mustafa, Aisyah Madihah and Ahd Suhaimi, Ahmad Basyir and Shahruddin, Najlah Sakinah and Abd Halim, Nor Farah Huda (2021) An experimental investigation on surface quality of CFRP after milling in cutting fluid environment. In: 7th International Conference on Applications and Design in Mechanical Engineering (ICADME 2021), 23 August 2021, Virtual.

Shahruddin, Najlah Sakinah and Mustaffa, Nur Haifa Syazwina and Mustafa, Aisyah Madihah and Abd Halim, Nor Farah Huda (2021) An experimental study of tool wear during end milling of carbon fibre reinforced polymer in cutting fluid condition. In: 7th International Conference on Applications and Design in Mechanical Engineering (ICADME 2021), 23 August 2021, UniMAP , Perlis.

Abd Halim, Nor Farah Huda and Ascrofta, Helen and Barnes, Stuart (2017) Analysis of tool wear, cutting force, surface roughness and machining temperature during finishing operation of ultrasonic assisted milling (UAM) of carbon fibre reinforced plastic (CFRP). In: Advances in Material and Processing Technologies Conference (AMPT 2017), 11th December 2017-14th December 2017, Chennai, India.

Abd Halim, Nor Farah Huda and Ascroft, Helen and Barnes, Stuart (2016) Machinability study of ultrasonic assisted machining (UAM) of carbon fibre reinforced plastic (CFRP) with multifaceted tool. In: 7th CIRP Conference on High Performance Cutting 2016, 31st May-2nd June 2016, Chemnitz; Germany.

Ascroft, Helen and Barnes, Stuart and Dahnel, Aishah Najiah and Gupta, Aniruddha and Abd Halim, Nor Farah Huda and Ray, David (2016) Ultrasonic assisted machining. In: The 17th International Conference on Machine Design and Production, 12th - 15th July 2016, Bursa, Turkiye.

Abd Halim, Nor Farah Huda and -, Afzeri and Aminanda, Yulfian (2011) Experimental study of cutting parameter for drilling on fabric carbon/epoxy composite laminates. In: 2011 International Conference on Advanced Design and Manufacturing Engineering, (ADME 2011), 16th-18th Sept. 2011, Guangzhou, China.

Wan Yusoff, Wan Ahmad Yusmawiza and Adesta, Erry Yulian Triblas and Dahnel, Aishah Najiah and Abd Halim, Nor Farah Huda (2011) The application of Quality Function Deployment (QFD) and Rapid Prototyping (RP) technology in improving the design of anti sleep driving alarm. In: Proceedings of the 2011 International Conference on Industrial Engineering and Operations Management, 22 - 24 Jan 2011, Kuala Lumpur, Malaysia.